Rayson LevelShield SL120 is a solvent-free, two-component, self-smoothing epoxy floor system that delivers a seamless wearing surface with medium to heavy chemical resistance and high mechanical strength.
Best for production areas, warehouses, loading bays and clean environments that need a seamless, hard-wearing, self-levelled epoxy floor.
LevelShield SL120 flows out under trowel, notched rake or roller into a seamless, self-smoothed wearing surface — the standard answer where roller-applied coatings are not enough and a level, joint-free floor is required. Solids content is 100% in both parts, so what goes down is what cures.
The cured floor combines medium to heavy chemical resistance with high mechanical strength: compressive strength up to 50 N/mm², Shore D hardness up to 70 and abrasion loss as low as 45 mg in standard Taber testing. That profile suits pharmaceutical facilities, clean rooms, assembly halls, plant rooms, garages, maintenance workshops and storage areas.
Being solvent-free, SL120 can be installed in enclosed and poorly ventilated spaces, and cure progresses predictably: foot traffic in 18–24 hours, light traffic in 2–4 days and full cure within about a week depending on temperature.
A body coat builds the main thickness and mechanical performance of the floor, applied over a primer and usually sealed with a finish.
The figures below are a guide for planning. Site conditions and workmanship affect results — confirm the details for your project with our technical team.
| Coverage | Approximately 1.6–2.0 kg/m² as a self-smoothing wearing coat, subject to filling grade, porosity, level variation and wastage |
|---|---|
| Mixing | Two pre-weighed parts, mix ratio 4:1 (A:B) by weight; mix mechanically for at least 2–3 minutes; pot life up to 20 minutes at 28 °C |
| Drying & curing | At +20 °C: foot traffic 24 h, light traffic 4 days, full cure 7 days. At +30 °C: foot traffic 18 h, light traffic 2 days, full cure 5 days. Recoat window 24 h–2 days at +20 °C (16 h–1 day at +30 °C) |
| Pack sizes | Part A 16 kg / Part B 4 kg per set |
It is applied as a self-smoothing wearing coat at a consumption of roughly 1.6–2.0 kg/m²; the achieved thickness depends on filling grade and levelness of the slab. Confirm the build-up for your traffic with our technical team.
Indicatively, foot traffic within about a day, light traffic in 2–4 days and full cure in 5–7 days depending on temperature — faster in warm conditions.
Yes. Apply over a suitable Rayson epoxy primer such as PrimeBond E20 on mechanically prepared concrete to guarantee adhesion and avoid pinholes from substrate porosity.
The system is rated for medium to heavy chemical resistance. For a specific chemical exposure — substance, concentration, temperature and contact time — always verify against the resistance schedule with our technical team.
Mixed material stays workable for only around 20 minutes at 28 °C and cures faster in bulk. Batching, placement and spike-rolling need to run as a continuous, well-crewed operation.
Yes — the seamless, easy-to-clean surface and solvent-free installation suit pharmaceutical facilities and clean rooms.
Rayson PrimeBond E20 is a two-component, medium-viscosity, solvent-free epoxy bonding primer that anchors resin floor systems to concrete, screed, asphalt and prepared metal — on dry or damp substrates.
View product
Rayson MortarBond EM90 is a three-pack, solvent-free epoxy mortar — resin, hardener and graded aggregate — that reinstates concrete floors with a non-shrink, highly abrasion-resistant repair.
View product
Rayson PatchBond TX80 is a two-component, solvent-free thixotropic epoxy adhesive and repair compound with exceptional sag resistance that bonds and fills on vertical, overhead and even mat-damp concrete surfaces.
View product
Rayson StaticGuard CX90 is a two-component, solvent-free conductive epoxy flooring that gives ESD-protected areas a self-smoothing, permanently conductive, chemically resistant wearing surface.
View productTell us your surface, area and timeline — our Singapore technical team will recommend a practical system and price it fast.
Rayson assistant
Answers from Rayson's own product information
Guidance only — confirm specifications with the Rayson technical team.