GripSafe acrylic
Rayson GripSafe AP12
Rayson GripSafe AP12 is a one-pack, self-crosslinking acrylic primer filler loaded with 0.5–1.5 mm silicate quartz aggregate that builds an anti-slip texture directly onto concrete and asphalt.
View productRayson UraForce HY15
Rayson UraForce HY15 is a single-component, water-based hybrid urethane — a self-crosslinking acrylic-copolymer-enhanced polyurethane — that roller-coats concrete and mineral surfaces with a fast-drying, stain-resistant, anti-slip finish.
Best for
Best for quick-turnaround coloured floor coating on walkways, playgrounds and commercial areas where single-pack simplicity and fast drying matter.
Overview
UraForce HY15 packs urethane performance into a one-can product. The self-crosslinking acrylic-copolymer-enhanced polyurethane needs no hardener or mix ratio — open, stir and roll — which removes the most common site errors and suits maintenance teams as well as applicators.
The film dries fast with well-balanced hardness and durability, and delivers good stain resistance, easy cleaning, low dirt pick-up, good abrasion resistance, anti-slip performance and water repellence. It is non-yellowing and suitable for interior or exterior use on grey concrete, stone, limestone, pavers and cementitious coatings.
Overcoating is possible in as little as 1–3 hours at 25 °C, with light traffic in roughly 4–6 hours — a genuinely fast programme for occupied sites and overnight windows.
Recommended uses
- Coloured coating over acrylic polymer cementitious coatings (APCC)
- Grey concrete walkways and commercial floors
- Hard surfaces such as stone and limestone
- Pavers, playgrounds and basketball courts
Suitable substrates
- Mineral substrates and grey concrete
- Stone and limestone
- Pavers
- Acrylic polymer cementitious coatings
Key benefits
- Single component — no mixing errors, minimal wastage
- Fast-drying: overcoat in 1–3 hours, light traffic in 4–6 hours at 25 °C
- Stain-resistant, easy-to-clean, anti-slip finish
- Non-yellowing, interior or exterior use
System position: Finish
A finish is the top coat. It provides the final appearance, cleanability and resistance to traffic, chemicals or UV.
Application method
- Brush
- Roller
Technical information
The figures below are a guide for planning. Site conditions and workmanship affect results — confirm the details for your project with our technical team.
| Coverage | Refer to TDS / contact technical team |
|---|---|
| Mixing | Single component, ready to use; pot life stated as under 4 hours once opened and in use |
| Drying & curing | Overcoat in 1–3 hours at 25 °C (substrate dependent); open to light traffic after 4–6 hours |
| Pack sizes | 24 kg plastic pail |
Limitations
- Ambient and surface temperatures must be at least 5 °C above the dew point
- Recommended wet film thickness approximately 130–150 microns per coat
- A thin-film finish, not a levelling or heavy-duty build product
- Shelf life shorter than two-pack products — rotate stock
Not suitable for
- Heavy industrial or forklift traffic — use an epoxy or PU-cement system
- Chemical spill or containment areas
- Levelling uneven substrates — it is a thin roller coat
Recommended systems
Fast-return walkway finish
- Prepare, clean and make good the surface
- Apply minimum 2 coats of Rayson UraForce HY15, overcoating within the recoat window
Anti-slip external ramp
- Prime and texture with Rayson GripSafe AP12 anti-slip primer filler
- Finish with Rayson UraForce HY15 in the selected colour
Frequently asked questions
Does UraForce HY15 need a hardener?
No — it is a single-component, self-crosslinking product. Stir well and apply; there is no mix ratio to get wrong.
How fast can an area reopen?
Indicatively, light foot traffic after 4–6 hours at 25 °C, with overcoating possible from 1–3 hours.
Is it slippery when wet?
The finish is formulated with anti-slip character, and for ramps or wet zones it pairs with GripSafe AP12 textured primer for a defined anti-slip profile.
Can it be used outdoors?
Yes — it is non-yellowing and suitable for interior or exterior use, including playgrounds, pavers and walkways.
How many coats are recommended?
A minimum of two, with dull patches receiving a further coat for a uniform finish.
Related products
UraForce polyurethane
Rayson UraForce WB52
Rayson UraForce WB52 is a two-component, water-based aliphatic urethane floor topcoat — low-VOC, low-odour and UV-resistant — that can be combined with broadcast aggregate for an anti-slip finish.
View product
PrimeBond acrylic
Rayson PrimeBond W10
Rayson PrimeBond W10 is a one-component, water-based acrylic primer, sealer and bonding agent for smooth concrete and mineral substrates, applied ahead of Rayson UraForce water-based topcoats.
View product
CourtFlex acrylic
Rayson CourtFlex AC25
Rayson CourtFlex AC25 is a single-component, water-based, self-crosslinking acrylic co-polymer coating for sports courts and decorative concrete and masonry surfaces, forming a stain-resistant, easy-to-clean film.
View productReady to specify Rayson UraForce HY15?
Tell us your surface, area and timeline — our Singapore technical team will recommend a practical system and price it fast.